Saturday, 09 21st

Last update03:04:50 AM

You are here: Home Optical Transceiver 10G SFP+ 8G SFP+ module Displaying items by tag: GPON
Monday, 29 October 2012 17:21

10G GPON ONU SFP,XG-PON1 ONU Transceiver

10G GPON ONU SFP,XG-PON1 ONU Transceiver

Features

  1.      Single fiber Bi-Directional transceiver with single mode SC receptacle
  2.      1270nm burst-mode 2.5Gbps transmitter with DFB laser
  3.      1577nm continuous-mode 9.953Gbps receiver with APD-TIA
  4.      Complies with ITU-T G.987.2 Class N1
  5.      Digital diagnostic interface compliant with SFF-8472 Rev 9.4 ,
  6.      Digital Diagnostic Monitoring (DDM) with external calibration
  7.      3.3V Single power supply
  8.      LVPECL interface logic level for data input
  9.     CML interface logic level for data output
  10.     Differential line input/output impedance 100 ohm
  11.     LVTTL for burst signal input and LOS detect output
  12.     Complies with RoHS directive (2002/95/EC)
  13.     Operating case temperature:
  • Standard :  0 to +70°C

Applications
Asymmetric 10G/2.5G Gigabit Passive Optical Network ONT

Description
The FTCS-10GONG-20X Bi-Directional Transceiver is the high performance module for single fiber communications by using 1270nm 2.5Gbps burst mode transmitter and 1577nm 9.953Gbps continuous receiver. The optical transceiver is compliant with the Small Form- Factor Pluggable (SFP) Multi-Source Agreement (MSA).
The transmitter section uses a 1270nm DFB laser diode with automatic power control (APC) function and temperature compensation circuitry to ensure stable extinction ratio over all operating temperature range, and full IEC825 and CDRH class 1 eye safety. The receiver has a hermetically packaged APD-TIA (trans-impedance amplifier) pre-amplifier and a limiting amplifier with CML compatible differential outputs.
The receiver section also provides LVTTL Loss of signal output (LOS). As the input optical power is decreased, LOS output switches from low to high (signal loss point). As the input optical power is increased from very low levels, LOS output will switch back from high to low (signal detection point). The level of signal detection point is at least 0.5 dB higher than the level of signal loss point. LVTTL logic interface simplifies interface to external circuitry.

Ordering information

Part Number

Product Description

FTCS-10GONG-20X

Tx1270nm, Rx1577nm, 2.5Gbps/9.953Gbps, Class N1, 0ºC ~ +70ºC with Digital Diagnostic Monitoring

Published in 10G GPON ONU
Monday, 29 October 2012 16:43

GPON ONU Class C+ SFP Transceiver

GPON ONU Class C+ SFP Transceiver

Features

  1.      Single fiber Bi-Directional transceiver with single mode SC receptacle
  2.      1310nm burst-mode 1.25Gbps transmitter with DFB laser
  3.      1490nm continuous-mode 2.5Gbps receiver with APD-TIA
  4.      Meets ITU-T G.984.2 Class C+
  5.      Digital diagnostic interface compliant with SFF-8472 Rev 9.4 ,
  6.      Digital Diagnostic Monitoring (DDM) with external calibration
  7.      3.3V Single power supply
  8.      LVPECL interface logic level for data input
  9.     CML interface logic level for data output
  10.     Differential line input/output impedance 100 ohm
  11.     LVTTL for burst signal input and signal detect output
  12.    Complies with RoHS directive (2002/95/EC)
  13.    Operating case temperature:
  •               Standard : 0 to +70°C
  •               Industrial : -40 to +85°C

Applications
Gigabit Passive Optical Network (GPON) ONU
Description
GNUP-3412S-C2CDA transceiver is a high performance module for single fiber communications using a 1310nm burst-mode transmitter and a 1490nm continuous-mode receiver. It is used in the optical network terminal (ONT) for GPON ONT Class C+ applications.
The Transmitter is designed for single mode fiber and operates at a nominal wavelength of 1310nm. The transmitter module uses a DFB laser diode with full IEC825 and CDRH class 1 eye safety. It contains APC functions, a temperature compensation circuit to ensure compliance with G.984.2 requirement at operating temperature, LVPECL data inputs and DC coupling circuit.
The receiver section uses a hermetic packaged APD TIA (APD with trans-impedance amplifier) and a limiting amplifier. The APD converts optical power into electrical current and the current is transformed to voltage by the trans-impedance amplifier. The differential DATA and /DATA CML data signals are produced by the limiting amplifier. The APD TIA is AC coupled to the limiting amplifier through a low pass filter. As the optical input power decreases, the Signal Detect will switch from high
to low (de-assert point). As the optical input power is increases, Signal Detect will switch back from low
to high (assert point). The assert level is at least 0.5 dB higher than the de-assert level (Signal Detect
Hysteresis).

Optical and Electrical Characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Transmitter

Tx Data Rate

RT

-

1.25

-

Gb/S

-

Centre Wavelength

λc

1260

1310

1360

nm

-

Spectral Width

∆λ

-

-

1

nm

-

Side Mode Suppression Ratio

SMSR

30

-

-

dB

-

Average Output Power

Pout

2

-

7

dBm

1

Extinction Ratio

ER

10

-

-

dB

-

Burst Enable Delay

Ton

-

-

12.86

ns

 

Burst Disable Delay

Toff

-

-

12.86

ns

 

Average Launch Power-OFF Transmitter

Poff

 

 

-41

dBm

 

Optical Rise/Fall Time (20%~80%)

tr/tf

 

 

260

ps

 

Data Input Swing Differential

VIN

200

 

1600

mV

2

Input Differential Impedance

ZIN

90

100

110

Ω

 

Burst

Disable

 

2.0

 

Vcc

V

 

Enable

 

0

 

0.8

V

 

TX Fault

Fault

 

2.0

 

Vcc

V

 

Normal

 

0

 

0.8

V

 

Receiver

Rx Data Rate

RR

-

2.5

-

Gb/s

3

Centre Wavelength

λc

1480

 

1500

nm

 

Receiver Sensitivity(BOL)

Sen

 

 

-30

dBm

3

Receiver Overload

Sat

-8

 

 

dBm

3

Receiver Reflectance

 

 

 

-20

dB

 

Signal Detect De-Assert

SDD

-44

 

 

dBm

 

Signal Detect Assert

SDA

 

 

-31

dBm

 

Signal Detect Hysteresis

SDH

0.5

 

6

dB

 

Output Differential Impedance

ZIN

90

100

110

Ω

 

Data Output Swing Differential

Vout

400

 

1000

mV

 

SD Output Voltage

High

 

2.0

 

Vcc

V

 

Low

 

0

 

0.8

V

 

Notes:

1. The optical power is launched into SMF.

2. PECL input, internally DC-coupled and terminated.

3. Measured with a PRBS 27-1 test pattern @1250Mbps, BER ≤1×10-10.

Ordering information

Part Number

Product Description

FTCS-ONG-20C

Tx1310nm, Rx1490nm, 1.25Gbps/2.5Gbps, Class C+, 0ºC ~ +70ºC with Digital Diagnostic Monitoring

FTCS-ONG-20CI

Tx1310nm, Rx1490nm, 1.25Gbps/2.5Gbps, Class C+, -40 to +85°Cwith Digital Diagnostic Monitoring

 

Published in GPON ONU
Monday, 29 October 2012 16:35

GPON ONU SFP,GPON ONU SFP Transceiver

GPON ONU SFP,GPON ONU SFP Transceiver

Features

  1.      Single fiber Bi-Directional transceiver with single mode SC receptacle
  2.      1310nm burst-mode 1.25Gbps transmitter with DFB laser
  3.      1490nm continuous-mode 2.5Gbps receiver with APD-TIA
  4.      Meets ITU-T G.984.2 Class B+
  5.      Digital diagnostic interface compliant with SFF-8472 Rev 9.4 ,
  6.      Digital Diagnostic Monitoring (DDM) with external calibration
  7.      3.3V Single power supply
  8.      LVPECL interface logic level for data input
  9.     CML interface logic level for data output
  10.     Differential line input/output impedance 100 ohm
  11.     LVTTL for burst signal input and signal detect output
  12.    Complies with RoHS directive (2002/95/EC)
  13.    Operating case temperature:
  • Standard : 0 to +70°C
  • Industrial : -40 to +85°C

Applications
Gigabit Passive Optical Network (GPON) ONU
Description
FTCS-ONG-20BX transceiver is a high performance module for single fiber communications using a 1310nm burst-mode transmitter and a 1490nm continuous-mode receiver. It is used in the optical network terminal (ONT) for GPON ONT Class B+ applications.
The Transmitter is designed for single mode fiber and operates at a nominal wavelength of 1310nm. The transmitter module uses a DFB laser diode with full IEC825 and CDRH class 1 eye safety. It contains APC functions, a temperature compensation circuit to ensure compliance with G.984.2 requirement at operating temperature, LVPECL data inputs and DC coupling circuit.
The receiver section uses a hermetic packaged APD TIA (APD with trans-impedance amplifier) and a limiting amplifier. The APD converts optical power into electrical current and the current is transformed to voltage by the trans-impedance amplifier. The differential DATA and /DATA CML data signals are produced by the limiting amplifier. The APD TIA is AC coupled to the limiting amplifier through a low pass filter. As the optical input power decreases, the Signal Detect will switch from high
to low (de-assert point). As the optical input power is increases, Signal Detect will switch back from low
to high (assert point). The assert level is at least 0.5 dB higher than the de-assert level (Signal Detect
Hysteresis).

Ordering information

Part Number

Product Description

FTCS-ONG-20B

Tx1310nm, Rx1490nm, 1.25Gbps/2.5Gbps, Class B+, 0ºC ~ +70ºC with Digital Diagnostic Monitoring

FTCS-ONG-20BI

Tx1310nm, Rx1490nm, 1.25Gbps/2.5Gbps, Class B+,- 40 to +85°C with Digital Diagnostic Monitoring

Published in GPON ONU
Sunday, 28 October 2012 15:22

GPON OLT SFP Class C+ Transceiver

GPON SFP OLT Class C+ Transceiver
Features

  1.      Single Fiber Transceiver with single mode SC receptacle
  2.      1490nm continuous-mode transmitter with DFB laser
  3.      1310nm burst-mode receiver with APD-TIA
  4.      Single 3.3V power supply
  5.      Reset burst-mode receiver design
  6.      Burst mode signal detect output which is LVTTL compatible.
  7.      Burst mode received signal strength indication (RSSI) output
  8.      Complies with ITU-T G984.2 Class C+
  9.      Digital diagnostic interface compliant with SFF-8472 Rev 9.4 ,
  10.      Complies with RoHS directive (2002/95/EC)
  11.      Operating case temperature:     
  •   Standard : 0 to +70°C
  •   Industrial : -40 to +85°C

Applications
 Gigabit Passive Optical Networks (G-PON) – OLT side
Description
The FTCS-OLG-20CX transceiver is the high performance module for single fiber by using 1490nm continuous-mode transmitter and 1310nm burst-mode receiver. It is optical line terminal(OLT) for ITU-T G984.2. The optical transceiver is compliant with the Small Form- Factor Pluggable (SFP) Multi-Source Agreement (MSA).
 The transmitter section uses a 1490nm DFB LD with automatic power control (APC) function and temperature compensation circuitry to ensure stable extinction ratio over all operating temperature range. and is ClassⅠlaser compliant IEC825 and CDRH standards.The receiver has a hermetically packaged burst-mode APD-TIA  (trans-impedance amplifier) pre-amplifier and a burst-mode limiting amplifier with LVPECL compatible differential outputs.
  The receiver also includes the function of burst mode signal detect output and fast RSSI output which is enabled by a trigger. When the burst optical power is on, the receiver outputs high level; when the burst optical power is off, the receiver outputs low level. Fast RSSI function can satisfy more severe timing demand to monitor the power from any ONU.

Ordering information

Part Number

Product Description

FTCS-OLG-20C

Tx1490nm, Rx1310nm , 2.5Gbps/1.25Gbps, Class C+, 0ºC ~ +70ºC With Digital Diagnostic Monitoring

FTCS-OLG-20CI

Tx1490nm, Rx1310nm , 2.5Gbps/1.25Gbps, Class C+-40 to +85°C With Digital Diagnostic Monitoring

 

Published in GPON OLT
Sunday, 28 October 2012 15:14

GPON OLT SFP,GPON OLT SFP Transceiver

GPON OLT SFP,GPON OLT SFP Transceiver
Features

  1.      Single Fiber Transceiver with single mode SC receptacle
  2.      1490nm continuous-mode transmitter with DFB laser
  3.      1310nm burst-mode receiver with APD-TIA
  4.      Single 3.3V power supply
  5.      Reset burst-mode receiver design
  6.      Burst mode signal detect output which is LVTTL compatible.
  7.      Burst mode received signal strength indication (RSSI) output
  8.      20Km Reach 28dB link budget
  9.      Complies with ITU-T G984.2 Class B+
  10.      Digital diagnostic interface compliant with SFF-8472 Rev 9.4 ,
  11.      Complies with RoHS directive (2002/95/EC)
  12.      Operating case temperature:
  •           Standard : 0 to +70°C
  •           Industrial : -40 to +85°C

Applications
 Gigabit Passive Optical Networks (G-PON) – OLT side

Description
The FTCS-OLG-20X transceiver is the high performance module for single fiber by using 1490nm continuous-mode transmitter and 1310nm burst-mode receiver. It is optical line terminal(OLT) for ITU-T G984.2. The optical transceiver is compliant with the Small Form- Factor Pluggable (SFP) Multi-Source Agreement (MSA).
 The transmitter section uses a 1490nm DFB LD with automatic power control (APC) function and temperature compensation circuitry to ensure stable extinction ratio over all operating temperature range. and is ClassⅠlaser compliant IEC825 and CDRH standards.The receiver has a hermetically packaged burst-mode APD-TIA  (trans-impedance amplifier) pre-amplifier and a burst-mode limiting amplifier with LVPECL compatible differential outputs.
  The receiver also includes the function of burst mode signal detect output and fast RSSI output which is enabled by a trigger. When the burst optical power is on, the receiver outputs high level; when the burst optical power is off, the receiver outputs low level. Fast RSSI function can satisfy more severe timing demand to monitor the power from any ONU.

Ordering information

Part Number

Product Description

FTCS-OLG-20B

Tx1490nm, Rx1310nm , 2.5Gbps/1.25Gbps, Class B+, 0ºC ~ +70ºC With Digital Diagnostic Monitoring

FTCS-OLG-20BI

Tx1490nm, Rx1310nm , 2.5Gbps/1.25Gbps, Class B+, -40 to +85°C With Digital Diagnostic Monitoring

 

Published in GPON OLT
Sunday, 28 October 2012 14:56

GPON ONU SFF 2X10 Transceiver

GPON ONU SFF 2X10 Transceiver

Features

  1.      Single fiber Bi-Directional transceiver with single SC/APC pigtail
  2.      1310nm burst-mode 1.25Gbps transmitter with DFB LD laser
  3.      1490nm continuous-mode 2.5Gbps receiver with APD-TIA
  4.      Burst mode:”high” active
  5.      Complies with ITU-T G.984.2 Class B+
  6.      Complies with Multi-Source Agreement (MSA) Small Form
  7.      Factor (SFF) 2x10 Footprint
  8.      Digital diagnostic interface compliant with SFF-8472 Rev 9.4 ,
  9.      Digital Diagnostic Monitoring (DDM) with external calibration
  10.      3.3V Single power supply
  11.      LVPECL interface logic level for data input
  12.     CML interface logic level for data output
  13.     Differential line input/output impedance 100 ohm
  14.     LVTTL for burst signal input and signal detect output
  15.     Complies with RoHS directive (2002/95/EC)
  16.     Operating case temperature:
  •           Standard : 0 to +70°C
  •           Industrial : -40 to +85°C

Applications

  1.      GPON ONU Class B+
  2.      Burst mode application.
  3.      FTTx broadband access system.

Description
The FTBF-ONG-20X Bi-Directional Transceiver is the high performance module for single fiber communications by using 1310nm 1.25Gbps burst mode transmitter and 1490nm 2.5Gbps continuous receiver. It is Optical Network Unit (ONU) for ITU-T G.984.2 Class B+. The optical transceiver is compliant with Multi-Source Agreement (MSA) Small Form Factor (SFF) 2x10 footprint.
The transmitter section uses a 1310nm DFB laser diode with automatic power control (APC) function and temperature compensation circuitry to ensure stable extinction ratio over all operating temperature range, and full IEC825 and CDRH class 1 eye safety. The receiver has a hermetically packaged PIN-TIA (trans-impedance amplifier) pre-amplifier and a limiting amplifier with CML compatible differential outputs.

Ordering information

Part Number

Product Description

FTBF-ONG-20

Tx1310nm, Rx1490nm, 1.25Gbps/2.5Gbps, class B+, Burst high, 0ºC ~ +70ºC with Digital Diagnostic Monitoring

FTBF-ONG-20I

Tx1310nm, Rx1490nm, 1.25Gbps/2.5Gbps, class B+, Burst high, -40 to +85°C with Digital Diagnostic Monitoring

Published in GPON ONU

Contact us

  • Add: Building 1,High-tech science technology industrial
    park,Chengdu,China
  • Tel: 0086-28-85255257

About us

Robot

F-tone is specializing in developing and manufacturing optical transceivers and components which are wildly applied in Datacon, Telecom and CATV, and provides customers with top quality and cost effective products. SFP,SFP光模块...

You are here: Home Optical Transceiver 10G SFP+ 8G SFP+ module Displaying items by tag: GPON