- HD-SDI SFP Transceiver available
- SD-SDI SFP Transceiver available
- 3G-SDI SFP Transceiver available
- SMPTE 297-2006 Compatible.
- Metal enclosure for Lower EMI
- 1310nm FP laser and PIN photodetector
- Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
- Digital Diagnostic Monitoring:
- Compatible with RoHS
- +3.3V single power supply
- Operating case temperature:
- Standard : 0 to +70°C
- Industrial : -40 to +85°C
Ordering information
Part Number |
Product Description |
FTCS-3G-SDI-T02 |
1310nm, 3Gbps, |
FTCS-3G-SDI-T02I |
1310nm, 3Gbps, |
FTCS-3G-SDI-T02D |
1310nm, 3Gbps, |
FTCS-3G-SDI-T02DI |
1310nm, 3Gbps, |
Pin Descriptions
Pin |
Signal Name |
Description |
Plug Seq. |
Notes |
1 |
VEET |
Transmitter Ground |
1 |
|
2 |
TX FAULT |
Transmitter Fault Indication |
3 |
Note 1 |
3 |
TX DISABLE |
Transmitter Disable |
3 |
Note 2 |
4 |
MOD_DEF(2) |
SDA Serial Data Signal |
3 |
Note 3 |
5 |
MOD_DEF(1) |
SCL Serial Clock Signal |
3 |
Note 3 |
6 |
MOD_DEF(0) |
TTL Low |
3 |
Note 3 |
7 |
Rate Select |
Not Connected |
3 |
|
8 |
NC |
|
|
|
9 |
VEER |
Receiver ground |
1 |
|
10 |
VEER |
Receiver ground |
1 |
|
11 |
VEER |
Receiver ground |
1 |
|
12 |
NC |
|
|
|
13 |
NC |
|
|
|
14 |
VEER |
Receiver ground |
1 |
|
15 |
VCCR |
Receiver Power Supply |
2 |
|
16 |
VCCT |
Transmitter Power Supply |
2 |
|
17 |
VEET |
Transmitter Ground |
1 |
|
18 |
TD+ |
Transmit Data In |
3 |
Note 4 |
19 |
TD- |
Inv. Transmit Data In |
3 |
Note 4 |
20 |
VEET |
Transmitter Ground |
1 |
|
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:
Low (0 to 0.8V): Transmitter on
(>0.8V, < 2.0V): Undefined
High (2.0 to 3.465V): Transmitter Disabled
Open: Transmitter Disabled
3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board. The pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
4) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.